| Customization: | Available |
|---|---|
| Media: | Gas, Oil, Water, Chemical |
| Temperature: | Low Temperature |
|
Still deciding? Get samples of US$ 2/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
American standard forged steel gate valve and flange gate valve belong to the same type of valve, the difference is that its closing part is a ball, and the ball rotates around the center line of the valve body to achieve opening and closing. Gate valves are mainly used to cut off, distribute and change the flow direction of media in pipelines. Two-piece ball valve and three-piece ball valve are a new type of valves widely used in recent years. Generally, these valves should be installed horizontally in pipelines.
The steel American Standard gate valve can be applied to water, steam, oil, nitric acid, acetic acid, strong oxidizing media and urea and other media. There are manual, bevel gear transmission and electric and so on. Structural features: 1. The fluid resistance is small, and the sealing surface is less brushed and eroded by the medium. 2. The opening and closing of the American standard gate valve is more labor-saving. 3. The flow direction of the medium is not restricted, and the flow is not disturbed and the pressure is not reduced. 4. The shape is simple, the structure length is short, the manufacturing process is good, and the application range is wide
Electric gate valve: An electric gate valve uses an electric motor instead of a handwheel. By utilizing electrical power, the actuator spins the stem to raise or lower the gate. This allows it to be operated remotely with no user on-site but requires electrical power on-site. These are also referred to as motorized gate valves.
A gate valve operates similar to other valves. To open the valve, turn the handwheel (A), which moves the gate (G) up or down on the stem (B) via the threads. A gate valve requires more than one 360° turn to open or close the valve fully. When the gate is lifted up, it opens the inlet to the outlet allowing an unobstructed passageway for the media to flow. When the gate is lowered, it closes and blocks the media flow.
The relationship between the gate's vertical travel and the flow rate is nonlinear for a gate valve, with the greatest changes occurring near-complete closure. When used to regulate flow, the relatively high velocity of the flow at partial opening results in gate and seat wear, which along with possible vibrations of the gate, shortens the valve's service life. Therefore, a gate valve should only be used for on/off control.
Pressure seal bonnet gate valves are ideal for high-pressure applications (more than 15 MPa). Pressure seal bonnets have a downward-facing cup inserted into the valve body. When internal fluid pressure increases, the cup is forced outward, improving the seal.
The gate is raised and lowered by the spinning of a threaded stem (Figure 2 Labeled B). As discussed, a manual wheel or actuator spins the stem. Depending on the design, it is either considered a rising stem gate valve or a non-rising stem gate valve. So, as you spin the stem, it either raises or stays in place with the spin.
Outside Screw and Yoke , also referred to as rising stems, are fixed to the gate. Therefore, the threads are on the actuation side. So, as the gate is raised or lowered, the stem moves with it up and down. Consequently, they have built-in visual indicators of the state of the valve and are easily lubricated. Since they have moving components, they cannot be used with bevel gears or actuators. Therefore, rising gate valves are suitable for manual actuation.
On the other hand, a non-rising stem is fixed to the actuator and threaded into the gate. An indicator is often threaded onto the stem to show the open or closed state of the valve. Non-rising gate valves are common in underground installations and applications with limited vertical space.
| Manufacture Standard Of Gate Valve | API 600 ASME B16.34 / KS B2361 / GB/T 12234 / DIN 3352 |
| Valve Connection | Flanged |
| Connection Type | ANSI, JIS, DIN, GB |
| Valve Material | CF8, CF8M, WCB |
| Power Supply | General: 3-phase 380VAC
Special: 3-phase AC660V, AC440V, AC415V Special: 1-phase AC220V, AC110V Special: DC12V, DC24V, DC48V |
| Torque Range | 50Nm to 10,000Nm |
| Protection Class | IP65 |
| Insulation Class | F Class |
| Ambient Temperature | -4°F to 140°F |
){kind=link}